Component library
Every part here has a reviewed pin map that the circuit builder and AI assistant use. Unknown parts are never drawn.
Development boards
ESP32 DevKit V1 (30-pin)
ESP32-WROOM-32 development board with Wi-Fi and Bluetooth, 3.3 V logic and USB power. Common 30-pin DOIT layout.
30 pins
ESP32-C3 Super Mini
Tiny RISC-V ESP32-C3 board with Wi-Fi and Bluetooth LE, USB-C, 3.3 V logic.
16 pins
Arduino Uno R3
ATmega328P board with 5 V logic, 14 digital and 6 analog pins.
29 pins
Raspberry Pi Pico
RP2040 microcontroller board with 26 GPIO, 3 ADC inputs and 3.3 V logic.
40 pins
Arduino Nano (ATmega328P)
Breadboard-friendly ATmega328P board with 5 V logic, 14 digital and 8 analog pins (A6/A7 analog-only). Same chip as the Uno.
30 pins
NodeMCU ESP8266 (ESP-12E, v3)
Low-cost Wi-Fi board with an ESP8266, 3.3 V logic, one analog input and micro-USB power.
19 pins
Wemos D1 Mini (ESP8266)
Compact ESP8266 Wi-Fi board with 11 digital pins, one analog input and USB power.
16 pins
Raspberry Pi Pico W
RP2040 board with on-board Wi-Fi and Bluetooth (CYW43439), same 40-pin header as the Pico, 3.3 V logic.
40 pins
Sensors
Capacitive Soil Moisture Sensor v1.2
Corrosion-resistant capacitive soil moisture probe with an analog output (higher reading = drier soil).
3 pins
Resistive Soil Moisture Module (LM393)
Two-prong resistive soil probe with comparator board giving analog and digital threshold outputs.
4 pins
DHT22 / AM2302 Module
Digital temperature and humidity sensor on a 3-pin breakout with on-board pull-up resistor.
3 pins
DS18B20 Waterproof Temperature Probe
1-Wire digital temperature probe in a stainless-steel tube.
3 pins
HC-SR04 Ultrasonic Distance Sensor
Ultrasonic ranging module, about 2 cm to 400 cm, 5 V supply.
4 pins
HC-SR501 PIR Motion Sensor
Passive infrared motion detector with adjustable sensitivity and delay; 3.3 V digital output.
3 pins
LDR Light Sensor Module
Photoresistor module with analog output and LM393 comparator digital output.
4 pins
MQ-2 Gas / Smoke Sensor Module
Combustible gas and smoke sensor with heated element; analog and digital outputs.
4 pins
BMP280 Pressure Sensor (3.3 V module)
Barometric pressure and temperature sensor on a 6-pin I2C/SPI breakout without a regulator.
6 pins
DHT11 Module
Basic digital temperature (0–50 °C) and humidity (20–90 %) sensor on a 3-pin breakout with pull-up.
3 pins
BME280 Module (I2C, 4-pin with regulator)
Temperature, humidity and pressure sensor on a 4-pin I2C breakout with on-board 3.3 V regulator.
4 pins
MPU-6050 Accelerometer + Gyro (GY-521)
6-axis motion sensor (3-axis accelerometer + 3-axis gyroscope) on the GY-521 I2C breakout with regulator.
8 pins
BH1750 Light Sensor (GY-302)
Digital ambient light sensor that reports lux over I2C.
5 pins
LM35 Temperature Sensor (TO-92)
Analog temperature sensor: 10 mV per °C (250 mV at 25 °C).
3 pins
IR Obstacle Sensor (FC-51)
Infrared reflective obstacle detector, 2–30 cm adjustable range, digital output (LOW when an object is detected).
3 pins
Rain Sensor Module (FC-37 / YL-83)
Rain-detection plate with comparator board: analog wetness level and digital rain output.
4 pins
Sound Sensor Module (KY-038)
Electret microphone with comparator: digital clap/noise trigger and analog envelope output.
4 pins
Flame Sensor Module (IR, 760–1100 nm)
Infrared flame detector with comparator: detects a candle/lighter flame at short range.
4 pins
Water Level Sensor (analog strip)
Exposed-trace water depth sensor (about 0–4 cm) with an analog output that rises with immersion.
3 pins
MQ-135 Air Quality Sensor Module
Heated gas sensor sensitive to ammonia, NOx, benzene, smoke and CO2; analog and digital outputs.
4 pins
ACS712 Current Sensor (5 A)
Hall-effect current sensor module: analog output centred at VCC/2, 185 mV per amp.
5 pins
RCWL-0516 Microwave Motion Sensor
Doppler radar motion detector that senses movement through thin plastic; 3.3 V digital output.
5 pins
IR Remote Receiver (VS1838B / KY-022)
38 kHz infrared receiver for TV remotes; demodulated digital output.
3 pins
Hall Effect Sensor Module (A3144 / KY-003)
Magnetic switch: output goes LOW when a magnet's south pole is near.
3 pins
HX711 Load Cell Amplifier
24-bit ADC module for load cells (weighing scales); two-wire digital interface (DT, SCK).
8 pins
Load Cell (5 kg bar)
Aluminium bar strain-gauge load cell (full bridge) for kitchen-scale projects. Use with an HX711.
4 pins
Displays
0.96" OLED 128×64 (SSD1306, I2C)
Monochrome 128×64 OLED display module using the SSD1306 controller over I2C.
4 pins
16×2 LCD with I2C Backpack (PCF8574)
Character LCD with PCF8574 I2C backpack and backlight; 5 V module.
4 pins
1.3" OLED 128×64 (SH1106, I2C)
Larger monochrome OLED using the SH1106 controller over I2C (needs an SH1106 driver, not SSD1306).
4 pins
20×4 LCD with I2C Backpack (PCF8574)
Four-line character LCD with PCF8574 I2C backpack and backlight; 5 V module.
4 pins
TM1637 4-Digit 7-Segment Display
Four-digit LED clock display with colon, driven by two wires (CLK, DIO).
4 pins
MAX7219 8×8 LED Matrix Module
Red 8×8 LED dot-matrix with MAX7219 driver; chainable for scrolling text.
5 pins
Actuators
1-Channel 5 V Relay Module
Single SPDT relay with transistor driver, indicator LED and flyback diode.
6 pins
SG90 Micro Servo
9 g hobby servo, 0–180°, controlled by a 50 Hz PWM signal.
3 pins
Active Buzzer Module
Buzzer module with built-in oscillator and transistor driver; sounds when the input is driven.
3 pins
Mini Submersible Water Pump (3–6 V DC)
Small brushed DC submersible pump for plant watering projects.
2 pins
TT Gear Motor (3–6 V DC)
Yellow plastic gear motor commonly used in robot car kits.
2 pins
2-Channel 5 V Relay Module
Two opto-isolated SPDT relays with drivers and indicator LEDs.
10 pins
L298N Dual Motor Driver
Dual H-bridge for two DC motors (or one stepper), up to ~2 A per channel, with on-board 5 V regulator.
13 pins
ULN2003 Stepper Driver Board
Darlington driver board for the 28BYJ-48 stepper motor, with LEDs for each coil.
11 pins
28BYJ-48 Stepper Motor (5 V)
Small geared unipolar stepper motor, ~2048 steps per revolution.
5 pins
MG996R Metal-Gear Servo
High-torque (~10 kg·cm) servo for robot arms and steering.
3 pins
12 V Solenoid Door Lock
Electromagnetic lock that retracts its latch while powered.
2 pins
Outputs
Passive parts
Resistor
Fixed through-hole resistor. Set its value in the properties panel.
2 pins
Electrolytic Capacitor
Polarised capacitor for power smoothing and decoupling. Set its value in the properties panel.
2 pins
Ceramic Capacitor
Small non-polarised capacitor (e.g. 100 nF decoupling).
2 pins
Diode 1N4007
1 A rectifier diode, commonly used as a flyback diode across motors, relays and solenoids.
2 pins
NPN Transistor BC547
General-purpose NPN transistor for switching small loads (≤100 mA) from a GPIO.
3 pins
Inputs
Tactile Push Button
Momentary normally-open switch. Shown as two terminals (the 4 legs are paired internally).
2 pins
Potentiometer 10 kΩ
Rotary potentiometer used as an adjustable voltage divider.
3 pins
TTP223 Capacitive Touch Button
Single-key capacitive touch module with digital output (HIGH when touched by default).
3 pins
Joystick Module (KY-023)
Two-axis analog joystick with push button.
5 pins
Rotary Encoder (KY-040)
Incremental rotary encoder with push button; quadrature CLK/DT outputs with pull-ups.
5 pins
4×4 Membrane Keypad
16-key matrix keypad: 4 row and 4 column lines scanned by the microcontroller.
8 pins
Power
5 V DC Supply (2 A)
Regulated 5 V supply, e.g. a USB power adapter on a breakout or a 5 V wall adapter.
2 pins
4×AA Battery Holder (6 V)
Four alkaline AA cells in series, about 6 V fresh, falling to ~4.4 V when depleted.
2 pins
LM2596 Buck Converter (set to 5 V)
Adjustable step-down regulator module. Assumed to be pre-adjusted to 5.0 V output.
4 pins
12 V DC Adapter (2 A)
12 V wall adapter for motors, LED strips and solenoids (via a barrel-jack breakout).
2 pins
9 V Battery (with snap)
PP3 9 V battery. Low capacity: fine for small Arduino projects, poor for motors.
2 pins
18650 Li-ion Cell + TP4056 Charger (protected)
Single 3.7 V Li-ion cell with a TP4056 USB charging board that includes over-discharge protection.
4 pins
AMS1117 3.3 V Regulator Module
Linear regulator board: 4.5–12 V in, 3.3 V out up to ~800 mA (less without a heatsink).
4 pins
MT3608 Boost Converter (set to 5 V)
Step-up converter module, assumed pre-adjusted to 5.0 V; turns a Li-ion cell into 5 V.
4 pins
Breadboard Power Supply (MB102)
Plug-in breadboard supply with 5 V and 3.3 V rails, powered by a 6.5–12 V adapter or USB.
4 pins
Solar Panel 6 V 1 W
Small monocrystalline panel (~6 V, ~170 mA in full sun) for charging projects.
2 pins
Communication modules
NEO-6M GPS Module (GY-NEO6MV2)
u-blox NEO-6M GPS receiver with antenna; sends NMEA sentences over UART at 9600 baud.
4 pins
HC-05 Bluetooth Module
Classic Bluetooth serial (SPP) module for phone-controlled projects; UART at 9600 baud by default.
6 pins
nRF24L01+ 2.4 GHz Radio
Low-power 2.4 GHz transceiver for board-to-board wireless links over SPI.
8 pins
RC522 RFID Reader (13.56 MHz)
MFRC522 RFID/NFC reader module for MIFARE cards and key tags over SPI.
8 pins