Skip to content
Circuits Playground
Menu

Electronics & IoT glossary

ADC (Analog-to-Digital Converter)

Converts a voltage into a number. An ADC turns an analog voltage into a digital value your code can use. The Arduino Uno's ADC is 10-bit (0–1023); the ESP32's is 12-bit (0–4095). Only ADC-capable pins can read analog sensors like soil-moisture probes or potentiometers.

Breadboard

A solderless board for prototyping circuits. A breadboard has rows of connected holes. The long rails along the sides carry power and ground. Parts and jumper wires push in without soldering, so circuits can be changed easily.

Buck converter

An efficient step-down voltage regulator. A buck converter such as the LM2596 steps a higher voltage (for example 12 V) down to a lower one (for example 5 V) by switching rapidly. It wastes far less heat than a linear regulator.

LM2596 buck module →

Common ground

All parts share the same 0 V reference. Every module that exchanges signals with a board must share its ground. Without a common ground, voltage levels are undefined and the circuit behaves erratically, even if each part has power.

Datasheet

The manufacturer's technical specification for a part. A datasheet lists a part's pinout, voltage and current limits and timing. Always check it before powering a new circuit; our component pages link to datasheets where available.

Debouncing

Ignoring the electrical noise of a mechanical switch. Buttons bounce for a few milliseconds when pressed, creating several transitions. Debouncing waits for the signal to settle, in code (with a short delay) or with an RC filter.

Flyback diode

Protects circuits from the voltage spike of a coil. When a motor or relay coil is switched off, its magnetic field collapses and produces a large reverse voltage. A flyback diode across the coil gives that energy a safe path. Relay modules usually include one.

GPIO

General-Purpose Input/Output pin. A GPIO is a microcontroller pin that your code can set as an input (to read a button or sensor) or an output (to drive an LED or relay input). A GPIO can only supply a few milliamps, so it should switch loads through a transistor, driver or relay.

ESP32 pinout →

I2C

A two-wire bus (SDA and SCL) for connecting many devices. I2C uses one data line (SDA) and one clock line (SCL), shared by every device on the bus. Each device has an address, such as 0x3C for an SSD1306 OLED. Both lines need pull-up resistors, which most breakout modules already include.

SSD1306 OLED →

IoT (Internet of Things)

Everyday devices connected to the internet. An IoT project connects sensors and actuators to a network so they can send data to a dashboard or be controlled remotely. Wi-Fi boards like the ESP32 are the most common starting point.

Logic level

The voltage that represents HIGH on a board. Boards run at either 5 V logic (Arduino Uno) or 3.3 V logic (ESP32, Pico). Connecting a 5 V output to a pin that isn't 5 V tolerant can damage it; use a level shifter or resistor divider.

Microcontroller

A small computer on one chip that runs a single program. A microcontroller combines a processor, memory and I/O pins. The ATmega328P (Arduino Uno), ESP32 and RP2040 (Pico) are microcontrollers. Unlike a Raspberry Pi computer, they run one program without an operating system.

MQTT

A lightweight publish/subscribe messaging protocol for IoT. MQTT devices publish messages to topics on a broker, and other devices or dashboards subscribe to those topics. It uses little bandwidth, so it suits microcontrollers on Wi-Fi.

Pull-up resistor

Holds a pin HIGH when nothing is driving it. A pull-up resistor connects a signal line to VCC so it reads HIGH by default instead of floating. Buttons wired to ground, I2C lines and 1-Wire buses (such as the DS18B20 with 4.7 kΩ) all need one.

PWM (Pulse-Width Modulation)

Fast on/off switching that simulates an analog level. PWM switches a pin on and off quickly. The fraction of time it is on (the duty cycle) sets the average power, which dims LEDs, controls motor speed and positions servos.

Relay

An electrically operated switch. A relay uses a small control current to switch a separate circuit through its COM, NO (normally open) and NC (normally closed) contacts. It isolates pumps, motors and lamps from the microcontroller.

5 V relay module →

SPI

A fast four-wire serial bus. SPI uses MOSI, MISO, SCK and a chip-select (CS/SS) line per device. It is faster than I2C and is common for SD cards, TFT displays and some sensors.

Strapping pins

Pins the chip reads at boot to choose a mode. On the ESP32, pins like GPIO0, 2, 12 and 15 are sampled at reset to set the boot mode and flash voltage. Pulling them the wrong way can stop the board from booting or uploading.

UART (Serial)

Two-wire asynchronous serial communication. UART sends data on TX and receives on RX. TX of one device connects to RX of the other. On most boards UART0 is used for USB programming and the Serial Monitor, so avoid using those pins for other parts.

Voltage divider

Two resistors that scale a voltage down. A voltage divider produces Vout = Vin × R2 / (R1 + R2). It is used to read 5 V signals on 3.3 V boards (for example the HC-SR04 Echo pin) or to measure battery voltage.

Voltage divider calculator →